N.Y.C. Jeep Club Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

ok guy's and gal's our membership application and due's for 2016 will be collected .you can down load print and fill out and bring to the next meet and greet's
If you will not be at the next meet and greet please PM me and i will give you my mailing address

Pages: [1] 2 3 4 5 6 7 8 ... 10
 1 
 on: August 02, 2018, 07:13:38 PM 
Started by EKAP - Last post by Andy5160
Nice and welcome !!!!!!!

 2 
 on: August 02, 2018, 07:13:01 PM 
Started by CMulzoff - Last post by Andy5160
Welcome !!!!!

 3 
 on: July 27, 2018, 07:29:05 PM 
Started by wb joe - Last post by MichaelRom
Canceled  too wet

 4 
 on: July 26, 2018, 06:30:13 AM 
Started by wb joe - Last post by MichaelRom
It's that time again. Hopefully the rain hold out

 5 
 on: July 23, 2018, 06:04:58 AM 
Started by stwilson74 - Last post by MichaelRom
That's great get a patten on it  8)  probably better than most shit out there

 6 
 on: July 22, 2018, 01:29:28 PM 
Started by stwilson74 - Last post by stwilson74
Over 2 and a half years later, tens of thousands of miles, still smooth as butter, can open and close with one finger, and no rattling.

Sent from my SM-N950U using Tapatalk


 7 
 on: June 29, 2018, 06:29:52 AM 
Started by wb joe - Last post by MichaelRom
Oh man the last Friday. I'll be there

 8 
 on: June 23, 2018, 07:29:27 PM 
Started by Dom - Last post by Dom
Good evening all. I hope that this post finds everyone well!

I am getting an error; C123C which is the dynamic yaw sensor. I have been to the dealership SIX times on this problem without resolution. So I am hoping that this is a problem that others have resolved successfully.

Some background info:

While parked on the street one evening, wheels turned out, a woman driving a Volvo was texting (she was honest with the police) and crashed into the front left wheel. What looked like a wheel alignment and front bumper turned into an $8000.00 repair job as Geico had EVERYTHING in the front replaced. The vehicle handles fine, the two new tires in the front have normal and even wear.

But now, it is 12,000 miles since it was repaired and I've begun getting this error code (C123C - Dynamic yaw Sensor).

At first, it was an occasional issue, but now it comes on regularly.

When the error happens:

It used to take a LOT to get the error to pop, but as miles have continued to pile on, it comes on easier and easier. I can tell you that it always comes on when I am steering to the right (coming around a bend) AND I hit a bump. And now, I don't have to hit a bump; I can be coming around a bend to the right and just go through a dip in the road which will trigger the error.

What's been done:

The Dynamic Yaw Sensor has been changed twice, the second time it was changed, it was changed along with the harness. In all, I've had two Dynamic sensors and TWO harnesses changed out. They also checked the harness in a spot that is prone to wear and sometimes shorts out to the chassis.

They also got Chrysler involved. They just don't know what the cause is.

What I've done

I am not a technical guy. When it comes to cars, In the words of the great ODDBALL from "Kelly's Heroes"; I ride 'em, I don't know what makes 'em work!

But I did some homework and found that the steering wheel was a bit off center, so, I centered it. I still get the error. Any chance it could be the speed sensor on the tire? I don't know.

But I am determined to get this issue resolved.

has anyone else lived through my scenario and figured out the problem?

Thank you in advance.

Dom


 9 
 on: June 19, 2018, 05:16:42 PM 
Started by Bobby718 - Last post by Bobby718
My upper ball joint on my 96 zj has recently inlarged its hole so when i press it back in after driving it pops back out. I searched on google and it looks like the only option is to weld the new one on or change the axle. I just regeard so the axle is staying. I do have a welder but would like to avoid that if possible. If anyone knows of any upgrades or has any ideas I am open to suggestions. Thank you

 10 
 on: June 12, 2018, 06:40:25 AM 
Started by MichaelRom - Last post by MichaelRom
Me too, we miss ya bud

Pages: [1] 2 3 4 5 6 7 8 ... 10